192.168.138.252
Private IP address · Device address · Network 192.168.138.0/24
192.168.138.252 is a private (RFC 1918) IP address that only works inside a local network, never on the internet. On a standard home network (192.168.138.0/24, mask 255.255.255.0) it is normally assigned to a device such as a phone, PC or printer, and the router is usually at 192.168.138.1.
- Type
- Private (RFC 1918)
- Role
- Device address
- Router (gateway)
- 192.168.138.1
192.168.138.252 is a private IPv4 address from the 192.168.0.0/16 block reserved for local networks. On a standard home network (192.168.138.0/24, subnet mask 255.255.255.0) it is a usable host address, often used for static assignments such as servers, NAS drives, cameras or access points.
How to find which device is using 192.168.138.252
- Check your router. Log in at 192.168.138.1 (or 192.168.138.254) and open Connected devices, DHCP clients or Attached devices. Find 192.168.138.252 in the list to see the device name and MAC address.
- Use the ARP table. On a computer on the same network, run
ping 192.168.138.252followed byarp -a. Look up the MAC address shown with our MAC Address Lookup to identify the manufacturer. - Try the web interface. Printers, cameras, NAS drives and access points often have a page at
http://192.168.138.252.
How to set 192.168.138.252 as a static IP
Best option: DHCP reservation: in your router at 192.168.138.1, open DHCP / LAN settings → Address reservation, choose the device (or enter its MAC address) and assign 192.168.138.252. The device always gets the same address and no conflicts occur.
Manual static IP on the device:
| IP address | 192.168.138.252 |
|---|---|
| Subnet mask | 255.255.255.0 (/24) |
| Default gateway | 192.168.138.1 |
| DNS servers | 192.168.138.1, or 1.1.1.1 / 8.8.8.8 |
Pick an address outside your router's DHCP pool for manual static IPs to avoid an "IP address conflict" error.
192.168.138.252 not reachable?
- Make sure your device is on the same
192.168.138.xnetwork: runipconfigand compare the first three numbers. - Run
ping 192.168.138.252. "Request timed out" means the device is off, asleep, or blocks ping with its firewall. - An "IP address conflict" means two devices use 192.168.138.252: restart both, or create a DHCP reservation.
- Disconnect from any VPN: it can route local traffic away from your network.
Useful commands for 192.168.138.252
Copy these to test or configure the device at 192.168.138.252 from a computer on the same network:
Windows
ping 192.168.138.252 tracert 192.168.138.252 arp -a | findstr 192.168.138.252 nslookup 192.168.138.252 netsh interface ip set address name="Wi-Fi" static 192.168.138.252 255.255.255.0 192.168.138.1
macOS
ping -c 4 192.168.138.252 traceroute 192.168.138.252 arp -a | grep "(192.168.138.252)" sudo networksetup -setmanual "Wi-Fi" 192.168.138.252 255.255.255.0 192.168.138.1
Linux
ping -c 4 192.168.138.252 ip neigh show 192.168.138.252 sudo nmcli con mod "<connection>" ipv4.method manual ipv4.addresses 192.168.138.252/24 ipv4.gateway 192.168.138.1
192.168.138.252 technical details
| IP address | 192.168.138.252 |
|---|---|
| Address type | Private (RFC 1918): 192.168.0.0/16, 16-bit block |
| Role on a /24 network | Device address |
| Position in 192.168.138.0/24 | 252 of 254 |
| Network / broadcast | 192.168.138.0/24 / 192.168.138.255 |
| Usable host range | 192.168.138.1 to 192.168.138.254 |
| Integer (decimal) | 3232271100 |
| Hexadecimal | C0.A8.8A.FC (0xC0A88AFC) |
| Octal | 0300.0250.0212.0374 |
| Binary | 11000000.10101000.10001010.11111100 |
| IPv4-mapped IPv6 | ::ffff:192.168.138.252 · ::ffff:c0a8:8afc |
| 6to4 prefix | 2002:c0a8:8afc::/48 |
| Reverse DNS (PTR) name | 252.138.168.192.in-addr.arpa |
192.168.138.252 in every subnet size
The same address belongs to a different network depending on the subnet mask. This table shows where 192.168.138.252 falls for each common prefix length:
| Prefix | Mask | Network | Broadcast | 192.168.138.252 is |
|---|---|---|---|---|
| /16 | 255.255.0.0 | 192.168.0.0 | 192.168.255.255 | host #35580 of 65534 |
| /20 | 255.255.240.0 | 192.168.128.0 | 192.168.143.255 | host #2812 of 4094 |
| /24 | 255.255.255.0 | 192.168.138.0 | 192.168.138.255 | host #252 of 254 |
| /25 | 255.255.255.128 | 192.168.138.128 | 192.168.138.255 | host #124 of 126 |
| /26 | 255.255.255.192 | 192.168.138.192 | 192.168.138.255 | host #60 of 62 |
| /27 | 255.255.255.224 | 192.168.138.224 | 192.168.138.255 | host #28 of 30 |
| /28 | 255.255.255.240 | 192.168.138.240 | 192.168.138.255 | host #12 of 14 |
| /29 | 255.255.255.248 | 192.168.138.248 | 192.168.138.255 | host #4 of 6 |
| /30 | 255.255.255.252 | 192.168.138.252 | 192.168.138.255 | network address |
Plan other ranges with the subnet calculator.
Common misspellings of 192.168.138.252
These won't open anything: IP addresses contain only digits and dots. Type 192.168.138.252 exactly:
192.168.138.252: FAQ
Is 192.168.138.252 a private IP address?
Yes. 192.168.138.252 is in the 192.168.0.0/16 private range (RFC 1918). It only works inside a local network and cannot be reached directly from the internet.
What device uses 192.168.138.252?
It depends on your network. Log in to your router at 192.168.138.1 and check the DHCP client / connected-devices list, or run "arp -a" on a computer on the same network.
Can I log in to 192.168.138.252?
Only if the device at 192.168.138.252 has a web interface (for example a printer, camera or NAS). Normally you log in to the router at 192.168.138.1 instead.
How do I give a device the IP 192.168.138.252?
In your router at 192.168.138.1, create a DHCP reservation for the device's MAC address with 192.168.138.252, or set a static IP on the device with subnet mask 255.255.255.0 and gateway 192.168.138.1.
What is 192.168.138.252 in binary and hexadecimal?
In binary 192.168.138.252 is 11000000.10101000.10001010.11111100; in hexadecimal it is C0.A8.8A.FC (0xC0A88AFC); as a single decimal number it is 3232271100.