192.168.9.133

Private IP address · Device address (DHCP pool) · Network 192.168.9.0/24

Quick answer

192.168.9.133 is a private (RFC 1918) IP address that only works inside a local network, never on the internet. On a standard home network (192.168.9.0/24, mask 255.255.255.0) it is normally assigned to a device such as a phone, PC or printer, and the router is usually at 192.168.9.1.

The address 192.168.9.133 belongs to the private 192.168.0.0/16 range, so it is only reachable inside a local network. On a standard home network (192.168.9.0/24, subnet mask 255.255.255.0) it is inside the default DHCP pool of many routers (for example 192.168.x.100 to .199), so it is usually assigned automatically to a phone, laptop or smart device.

About the 192.168.9.x network

192.168.9.0/24 is used by several 4G/5G home routers. You will typically find it on:

  • 4G/5G CPE routers
  • Wavlink extenders

How to find which device is using 192.168.9.133

  1. Check your router. Log in at 192.168.9.1 (or 192.168.9.254) and open Connected devices, DHCP clients or Attached devices. Find 192.168.9.133 in the list to see the device name and MAC address.
  2. Use the ARP table. On a computer on the same network, run ping 192.168.9.133 followed by arp -a. Look up the MAC address shown with our MAC Address Lookup to identify the manufacturer.
  3. Try the web interface. Printers, cameras, NAS drives and access points often have a page at http://192.168.9.133.

How to set 192.168.9.133 as a static IP

Best option: DHCP reservation: in your router at 192.168.9.1, open DHCP / LAN settings → Address reservation, choose the device (or enter its MAC address) and assign 192.168.9.133. The device always gets the same address and no conflicts occur.

Manual static IP on the device:

IP address192.168.9.133
Subnet mask255.255.255.0 (/24)
Default gateway192.168.9.1
DNS servers192.168.9.1, or 1.1.1.1 / 8.8.8.8

Pick an address outside your router's DHCP pool for manual static IPs to avoid an "IP address conflict" error.

192.168.9.133 not reachable?

  • Make sure your device is on the same 192.168.9.x network: run ipconfig and compare the first three numbers.
  • Run ping 192.168.9.133. "Request timed out" means the device is off, asleep, or blocks ping with its firewall.
  • An "IP address conflict" means two devices use 192.168.9.133: restart both, or create a DHCP reservation.
  • Disconnect from any VPN: it can route local traffic away from your network.

Useful commands for 192.168.9.133

Copy these to test or configure the device at 192.168.9.133 from a computer on the same network:

Windows

ping 192.168.9.133
tracert 192.168.9.133
arp -a | findstr 192.168.9.133
nslookup 192.168.9.133
netsh interface ip set address name="Wi-Fi" static 192.168.9.133 255.255.255.0 192.168.9.1

macOS

ping -c 4 192.168.9.133
traceroute 192.168.9.133
arp -a | grep "(192.168.9.133)"
sudo networksetup -setmanual "Wi-Fi" 192.168.9.133 255.255.255.0 192.168.9.1

Linux

ping -c 4 192.168.9.133
ip neigh show 192.168.9.133
sudo nmcli con mod "<connection>" ipv4.method manual ipv4.addresses 192.168.9.133/24 ipv4.gateway 192.168.9.1

192.168.9.133 technical details

IP address192.168.9.133
Address typePrivate (RFC 1918): 192.168.0.0/16, 16-bit block
Role on a /24 networkDevice address (DHCP pool)
Position in 192.168.9.0/24133 of 254
Network / broadcast192.168.9.0/24 / 192.168.9.255
Usable host range192.168.9.1 to 192.168.9.254
Integer (decimal)3232237957
HexadecimalC0.A8.09.85 (0xC0A80985)
Octal0300.0250.011.0205
Binary11000000.10101000.00001001.10000101
IPv4-mapped IPv6::ffff:192.168.9.133 · ::ffff:c0a8:985
6to4 prefix2002:c0a8:0985::/48
Reverse DNS (PTR) name133.9.168.192.in-addr.arpa

192.168.9.133 in every subnet size

The same address belongs to a different network depending on the subnet mask. This table shows where 192.168.9.133 falls for each common prefix length:

PrefixMaskNetworkBroadcast192.168.9.133 is
/16255.255.0.0192.168.0.0192.168.255.255host #2437 of 65534
/20255.255.240.0192.168.0.0192.168.15.255host #2437 of 4094
/24255.255.255.0192.168.9.0192.168.9.255host #133 of 254
/25255.255.255.128192.168.9.128192.168.9.255host #5 of 126
/26255.255.255.192192.168.9.128192.168.9.191host #5 of 62
/27255.255.255.224192.168.9.128192.168.9.159host #5 of 30
/28255.255.255.240192.168.9.128192.168.9.143host #5 of 14
/29255.255.255.248192.168.9.128192.168.9.135host #5 of 6
/30255.255.255.252192.168.9.132192.168.9.135host #1 of 2

Plan other ranges with the subnet calculator.

Common misspellings of 192.168.9.133

These won't open anything: IP addresses contain only digits and dots. Type 192.168.9.133 exactly:

1921689133l92.l68.9.l33192,168,9,133192 168 9 133192.168.9133http //192.168.9.133https://192.168.9.133192.168.9.133/admin

192.168.9.133: FAQ

Is 192.168.9.133 a private IP address?

Yes. 192.168.9.133 is in the 192.168.0.0/16 private range (RFC 1918). It only works inside a local network and cannot be reached directly from the internet.

What device uses 192.168.9.133?

It depends on your network. Log in to your router at 192.168.9.1 and check the DHCP client / connected-devices list, or run "arp -a" on a computer on the same network.

Can I log in to 192.168.9.133?

Only if the device at 192.168.9.133 has a web interface (for example a printer, camera or NAS). Normally you log in to the router at 192.168.9.1 instead.

How do I give a device the IP 192.168.9.133?

In your router at 192.168.9.1, create a DHCP reservation for the device's MAC address with 192.168.9.133, or set a static IP on the device with subnet mask 255.255.255.0 and gateway 192.168.9.1.

Who uses the 192.168.9.x network?

192.168.9.0/24 is used by several 4G/5G home routers. It is used by 4G/5G CPE routers, Wavlink extenders.

What is 192.168.9.133 in binary and hexadecimal?

In binary 192.168.9.133 is 11000000.10101000.00001001.10000101; in hexadecimal it is C0.A8.09.85 (0xC0A80985); as a single decimal number it is 3232237957.