Kti Default Password
Switches & Enterprise Networking · 3 default logins · Updated
The most common default login for Kti devices is username "admin" and password "123456". There are 3 known default combinations listed below; which one works depends on the model and firmware. Change the default password as soon as you sign in, because default logins are public and widely scanned for.
- Most common username
admin- Most common password
123456- Known combinations
- 3
Looking for the default login of a Kti switch or network device? Below are the documented factory credentials. Kti has 3 documented default logins. The most common username is admin (2 entries) and the most common password is 123456 (2 entries).
Kti default username and password list
| # | Username | Password | Type | Notes |
|---|---|---|---|---|
| 1 | admin | 123 | Numeric PIN | — |
| 2 | admin | 123456 | Numeric PIN | — |
| 3 | superuser | 123456 | Numeric PIN | — |
"(blank)" means leave the field empty. Source: CIRT.net default password database (via SecLists, MIT). Defaults can differ by model and firmware: check the label on your device.
What these Kti defaults tell you
- 3 are numeric PINs, typical for keypads and service menus.
- Kti has the 86th longest default-credential list of the 283 vendors in our database.
Kti default login at a glance
| Brand | Kti |
|---|---|
| Category | Switches & Enterprise Networking |
| Known default logins | 3 |
| Unique usernames | 2 |
| Unique passwords | 2 |
| Blank passwords | 0 of 3 |
| List size rank | 86th of 283 brands |
| Shares a login with | No other brand |
How to log in to a Kti switch or network device
- Many Kti models use serial console cable (RJ-45 or DB-9, typically 9600 baud, 8-N-1)
- Kti admins often use sSH or Telnet to the management IP
- With Kti hardware, web management interface (HTTP/HTTPS) on managed models
- On Kti equipment, sNMP (read/write community strings) for monitoring
Which login to try, in order:
- First, try username admin with password 123.
- If that fails, use username admin with password 123456.
- Next, try username superuser with password 123456.
Forgot the password? Reset your Kti switch or network device
- For Kti units, connect a console cable and power-cycle the device.
- Interrupt the boot sequence (Break key or the vendor’s mode button) to enter recovery / ROMMON mode.
- Skip or erase the startup configuration and reboot.
- Log in with the factory credentials and set a new password before saving.
Why you should change the Kti default password
- Risk for Kti owners: full control of VLANs, routing and traffic mirroring.
- With Kti defaults unchanged, default SNMP community strings ("public"/"private") leak or change configuration.
- If a Kti switch keeps its factory login: telnet sends credentials in clear text: use SSH.
How to change it: Kti recommends changing the factory login at first setup. From the CLI enter configuration mode, set a new enable/admin secret and user password, disable Telnet in favour of SSH, change SNMP communities and save the running configuration. Create a strong replacement with our password generator.
Kti default password FAQ
What is the default password for Kti?
The most common default is "123456". All 3 known combinations are listed in the table above: the right one depends on the product and firmware.
What is the default Kti username?
Common default usernames are "admin", "superuser".
How do I log in to a Kti switch or network device?
Many Kti models use serial console cable (RJ-45 or DB-9, typically 9600 baud, 8-N-1). On the login screen enter username admin with password 123.
The Kti default password doesn't work: what now?
If admin / 123 is rejected, someone changed it after installation. For Kti units, connect a console cable and power-cycle the device. Interrupt the boot sequence (Break key or the vendor’s mode button) to enter recovery / ROMMON mode.
Is it safe to keep the Kti default password?
No. Risk for Kti owners: full control of VLANs, routing and traffic mirroring. Kti recommends changing the factory login at first setup. From the CLI enter configuration mode, set a new enable/admin secret and user password, disable Telnet in favour of SSH, change SNMP communities and save the running configuration.