Develcon Default Password

Switches & Enterprise Networking · 2 default logins · Updated

Quick answer

The most common default login for Develcon devices is username blank (leave it empty) and password "BRIDGE". There are 2 known default combinations listed below; which one works depends on the model and firmware. Change the default password as soon as you sign in, because default logins are public and widely scanned for.

Use this reference to log in to a Develcon switch or network device that is still on its factory settings. Develcon has 2 documented default logins. The most common username is (blank) (2 entries) and the most common password is BRIDGE.

Develcon default username and password list

#UsernamePasswordTypeNotes
1(blank)BRIDGEProduct-specific—
2(blank)passwordCommon word—

"(blank)" means leave the field empty. Source: CIRT.net default password database (via SecLists, MIT). Defaults can differ by model and firmware: check the label on your device.

What these Develcon defaults tell you

  • 2 entries have no username: type only the password.
  • Develcon has the 106th longest default-credential list of the 283 vendors in our database.
  • 7 other vendors use at least one of the same username/password pairs, which is why attackers try these combinations first.

Develcon default login at a glance

BrandDevelcon
CategorySwitches & Enterprise Networking
Known default logins2
Unique usernames1
Unique passwords2
Blank passwords0 of 2
List size rank106th of 283 brands
Shares a login with7 other brands

How to log in to a Develcon switch or network device

  • Develcon admins often use serial console cable (RJ-45 or DB-9, typically 9600 baud, 8-N-1)
  • With Develcon hardware, sSH or Telnet to the management IP
  • On Develcon equipment, web management interface (HTTP/HTTPS) on managed models
  • For a Develcon switch, sNMP (read/write community strings) for monitoring

Which login to try, in order:

  1. First, try username (blank) with password BRIDGE.
  2. If that fails, use username (blank) with password password.

Forgot the password? Reset your Develcon switch or network device

  1. Connect a console cable and power-cycle the device.
  2. Interrupt the boot sequence (Break key or the vendor’s mode button) to enter recovery / ROMMON mode.
  3. Skip or erase the startup configuration and reboot.
  4. Log in with the factory credentials and set a new password before saving.

Why you should change the Develcon default password

  • Risk for Develcon owners: full control of VLANs, routing and traffic mirroring.
  • With Develcon defaults unchanged, default SNMP community strings ("public"/"private") leak or change configuration.
  • If a Develcon switch keeps its factory login: telnet sends credentials in clear text: use SSH.

How to change it: Develcon recommends changing the factory login at first setup. From the CLI enter configuration mode, set a new enable/admin secret and user password, disable Telnet in favour of SSH, change SNMP communities and save the running configuration. Create a strong replacement with our password generator.

Develcon default password FAQ

What is the default password for Develcon?

The most common default is "BRIDGE". All 2 known combinations are listed in the table above: the right one depends on the product and firmware.

What is the default Develcon username?

The default username is "(blank)".

How do I log in to a Develcon switch or network device?

Develcon admins often use serial console cable (RJ-45 or DB-9, typically 9600 baud, 8-N-1). On the login screen enter username (blank) with password BRIDGE.

The Develcon default password doesn't work: what now?

If (blank) / BRIDGE is rejected, someone changed it after installation. Connect a console cable and power-cycle the device. Interrupt the boot sequence (Break key or the vendor’s mode button) to enter recovery / ROMMON mode.

Is it safe to keep the Develcon default password?

No. Risk for Develcon owners: full control of VLANs, routing and traffic mirroring. Develcon recommends changing the factory login at first setup. From the CLI enter configuration mode, set a new enable/admin secret and user password, disable Telnet in favour of SSH, change SNMP communities and save the running configuration.